How to read the old Bora data stream in 431 (analysis of Bora 1.8t data stream)

US 2023-05-27 08:12:40 3 0

1. Manual matching method for remote controller of FAW-Volkswagen sagitar.

Open the driver's door, turn the ignition switch on and off for three times without pulling out the remote control key;

Close and open the driver's side door for 3 times, and then enter the learning state when the door locks;

Press any key on the remote control twice to lock the door;

Pull out the remote control key and the door lock moves again, which means that the remote control is successfully matched.

2. Matching setting of Volkswagen Jetta remote control key

The remote control key matching settings for Type I are as follows.

The remote controller part number is 1GD 962 258, and the chassis number is before LFV2A11G753136244. Remote controller part number reading method: Enter address 05 through value-added service 5051 5052, with the words "1GD 962 258" in the upper right corner.

The detailed operation steps are as follows.

The adaptation of the first key is as follows.

1) Turn the ignition key to be matched on/off for 3 times in the ignition switch to complete initialization. It is required that the total time of opening/closing for three times should not exceed 5s. Pull out the ignition key.

2) Press and hold any key of the key.

3) Press another key three times within 10s.

4) Release all keys.

5) The LED light of the key flashes 5 times.

6) At this point, the first key adaptation is completed.

Adaptation of the second key: Repeat steps 2)~5) in step.

pay attention to

There is no need to re-initialize the second key, but the time from the end of the last key adaptation cannot exceed 20 years old.

When the key is initialized again or the ignition switch is turned on, or the receiving period ends, the key matching process will be interrupted.

The remote control key matching settings applicable to Type 2 are as follows.

The control unit of comfort system is a Jetta with part number 1GD 959 875 D and version number 0200. Reading method of control unit part number: Enter address 05 through value-added service 5051 5052, with words "1GD 959 875 D" and "0200" in the upper right corner.

The detailed operation steps are as follows.

The adaptation of the first key is as follows.

1) Turn the ignition key to be matched on/off for 3 times in the ignition switch with an interval of 0.1 ~ 1s.

2) After hearing the short tone prompt from the controller, pull out the ignition key.

3) Press and hold any key of the key, and do not release it.

4) Press and hold another key of the key, that is, press and hold two keys at the same time.

5) After hearing the controller prompt, release all keys.

6) At this point, the first key adaptation is completed.

Adaptation of the second key: Repeat steps 3) ~ 5) in step. Each car can match up to 4 remote control keys.

pay attention to

Steps 2) ~ 5) must be completed within 2s.

If multiple remote control keys need to be matched, the time interval between two adjacent keys cannot exceed 2s.

If the following operations are not continued after the matching work is carried out in step 1), the original matched remote control key will be invalid. Pay attention to "A13552086073" for more surprises!

The remote control key matching settings applicable to Type 3 are as follows.

The control unit of comfort system is a Jetta with part number 1GD 959 875 D and version number 0300. Reading method of control unit part number: enter the address 05 through VAS 5051＼5052, with the words "1GD 959 875 D" and "0300" in the upper right corner.

The detailed operation steps are as follows.

The matching method is the same as that of Type 2 vehicles.

pay attention to

All remote control keys must be matched within 15s after step 1) is completed.

When any of the following conditions are met, the matching process ends.

1) Turn on the ignition switch.

2) Remote control key matching is completed.

3) More than 15s after completing step 1).

If the following operations are not continued after the matching work is carried out in step 1), the original matched remote control key is still valid.

Description:

Address 05 block reading function: Address 05→08→01 can read the number of remote control keys.

3. Volkswagen Bora remote control key matching

The operation process is as follows.

Use the key to turn KL15 on/off three times in 5s.

When the turn signal flashes 1, it prompts to enter the initialization state and start timing.

Press and hold any key on/off of the remote control key, and then press the other key on/off of the remote control key immediately. The turn signal flashes once to indicate that the initialization is successful.

Repeat the operation steps to initialize another remote control key, and a total of four remote control keys can be initialized.

4. Manual matching process of Volkswagen Bora GP MJ08 remote control key

After continuously turning on/off the ignition switch for three times within 5s, the controller will be prompted to enter the initialization state by flashing the turn signal once. The initialization state is maintained for 15s. During this time, the controller is ready to receive the initialization code from the remote control key. Pay attention to "A13552086073" for more surprises!

The specific operation process is as follows.

Use the key to turn KL15 on/off three times in 5s.

When the turn signal flashes 1, it prompts to enter the initialization state and start timing.

Repeat the operation steps to initialize another remote control key, and a total of four remote control keys can be initialized.

note:

The whole initialization process must be completed within 15s; After 15s, turn on the ignition switch or initialize 4 remote control keys to exit the initialization state.

When a new remote control key is successfully initialized, all the original remote control key information will be cleared. That is to say, if you want to use several remote control keys to operate the vehicle, you must initialize several keys in the same initialization process.

5. Matching settings for changing the remote control keys of Volkswagen Sagitar and Golf.

Disassembly process:

1) Turn on the ignition switch, use VAS 5051 to enter 46 comfort system, and 10 matches to clear the learning value;

2) Remove the key and pull out the transmitter.

Install the transmitter:

1) Pay attention to "A13552086073" for more surprises! Install a new transmitter;

2) Turn on the ignition switch, use VAS 5051 to enter 46 comfort system, 10 match channel 1, and select 2 to save;

3) Remove the key, close all the doors, and press and hold the locking key within 3s. After the doors are locked, press and unlock the doors, and then press and hold the trunk lid button, so that the trunk lid pops up and the transmitter matches successfully.

Precautions:

1) When replacing the transmitter, prompt the user to bring another remote control key to the service station for matching, otherwise the remote control will not be used;

2) Close the door and press the locking key within 3s.

6. Matching method of Volkswagen's new Jetta GIF remote control key

The matching method of the first key is as follows.

2) Press and hold any key of the key.

3) Press another key three times within 10s.

4) Release all keys.

5) The LED light of the key flashes 5 times.

6) At this point, the first key adaptation is completed.

Matching the second key: repeat steps 2) ~ 5).

The precautions are as follows.

1) The second key does not need to be re-initialized, but the time from the end of the last key adaptation cannot exceed 20s.

2) Initialize the key again or turn on the ignition switch, or the receiving period ends, and the key matching process will be interrupted.

7.2010 Volkswagen New Bora Remote Control Matching

The remote control matching steps are as follows.

The main door is opened, and the key switch is not pulled for three times.

Close/open the door for 3 times and lock it, then enter the learning state.

Press any key of the remote controller twice to lock the door.

Pull out the key and lock the door again, and the remote controller is successfully matched.

The programming operation of remote control circuit board is as follows.

Pay attention to "A13552086073" for more surprises! Open the driver's door.

Lock the door once and unlock it once with the unlock key on the door.

Insert the key into the lock hole.

Turn the key to ON, then turn it back to LOCK, do it three times in 10s, and finally stop at LOCK.

Close the door and open it three times, and finally open the door.

The car's computer should react at this time, showing that it automatically locks the door once and unlocks it once.

Press any button on each remote control twice, and the computer should lock the door and unlock it once.

Pull out the key, and the computer will make the last response, which is about four consecutive door locks and unlocks.

8. Volkswagen Golf A6 remote control key matching

Turn on the ignition switch, connect the computer detection instrument and enter address 46;

Select function 10, select channel 00, and delete the adaptation memory;

Select function 10, select channel 01, and enter the number of matching keys "00001-"4 ";

In turn, the remote control keys on the keys that are adapted as needed are more than 1s. Pay attention to "A13552086073" for more surprises! All keys should be completed within 15s;

Turn on the ignition switch with the non-expired remote control key.

For the new remote controllers of Bora and Golf Cars, the matching process of new remote control keys can be used:

Turn on the ignition switch with the remote control key that has not expired;

Lock the door with a new key;

Open or close the door with the remote control key;

Press the remote control button after the key stops for at least 1s;

There is a horn prompt at the end of adaptation.

9. Matching of Volkswagen Santana 3000 remote key device

Initialization, applicable to the new transmitter, the new transmitter and the original transmitter must be initialized with the receiver. If the user loses a transmitter and cannot get a new transmitter temporarily, the original transmitter should be reinitialized to make the lost transmitter invalid.

The matching steps are as follows:

1) Turn off the ignition switch;

2) All door contact switches are disconnected;

3) grounding the programming line;

4) Turn on the ignition switch;

5) Turn off the ignition switch again;

6) Pay attention to "A13552086073" for more surprises! The remote control receiver enters 60s programming mode;

7) If the doors are closed, all doors will be unlocked to indicate that the remote control receiver enters the programming mode;

8) Press any button of the remote transmitter twice within 10s, with an interval of about 2s;

9) After the programming is completed, the door lock will be locked and unlocked once to confirm;

10) Repeat steps 8) and 9) for the second remote control transmitter;

11) The programming line is restored, and the initialization is finished.

The remote control transmitter and remote control receiver are resynchronized, which is suitable for the original remote control transmitter to be pressed continuously for 255 times beyond the effective remote control distance, or the remote control transmitter and remote control receiver will not be synchronized, and the door lock can no longer be remotely opened and closed, so it is necessary to resynchronize.

The matching steps are as follows:

1) Close all the doors, so that the door locks are in the open state;

2) Turn on the ignition switch;

3) Press the open key of the remote control transmitter once within 30s;

4) If the synchronization is successful, the door lock will be locked and opened once each to confirm.

10. Volkswagen Goyle Remote Control Key Matching

Matching of Shanghai Volkswagen Goyle Remote Control Key The matching of Shanghai Volkswagen Goyle Remote Control Key is as follows.

Initial matching steps:

1) Insert the key into the driver's door lock cylinder and turn it counterclockwise;

2) Keep the key in this position, wait for more than 3s, and pay attention to "A13552086073" for more surprises! Then press any remote control button on this key for many times until the locking button automatically locks and unlocks once each to show that the remote control system has been correctly matched;

3) Turn the key back to its original position, and do not press any remote control button on this key;

4) Repeat this process for the remaining keys, and the initial matching work is completed.

pay attention to

For the remote controller using the original vehicle, it should be kept waiting for more than 3 hours under the normal power-on state, and do not press any button of the remote transmitter of the original vehicle within this 3 hours. After 3 hours, the above initialization process is carried out again.

The transmitter of the original vehicle must be initialized at the same time.

Synchronous matching steps:

1) Turn on the ignition switch;

2) Keep the key in this position, and press any remote control button on this key for many times until the door lock is locked and opened once each to show that the remote control system has been correctly matched;

3) Turn off the ignition switch, and the synchronous work is over.

pay attention to

Pay attention to the following two points for the initialization procedure.

Pay attention to "A13552086073" for more surprises! The vehicle does not have to be locked in the first step.

The second step says, "Wait for more than 3s, and then press any remote control button on this key several times". Please note that there should be a certain interval in this multiple times, that is to say, every time you press it, you will stop, otherwise you may press it again after matching.

11. Remote control matching of Volkswagen PQ35 platform model

Open the plastic cover of the driver's side door handle;

Press the unlock button of the remote controller;

Turn the door lock to "lock the door" with the small key in the remote control;

Press the unlock button of the remote controller again;

Complete synchronization.

12. Volkswagen Santana Zhijun Remote Control Matching

Method 1:

People sit in the cab and close all the doors;

Press the cab door lock;

Insert the ignition key, turn it from OFF gear to ACC gear for 3 times, and finally stop at ON position. At this time, the cab door lock will pop up and pull out the key;

Press the cab door lock again;

Press the remote control lock key once, the cab door lock pops up, and the first remote control is matched;

Then press the locking key of the second remote control, and the cab door lock pops up again, and the second match is completed;

Match 6 keys at most, and the matching of the 5th and 6th keys must be completed within 5s.

Method 2:

Close all doors and people sit in the cab;

Press the cab door lock;

Insert the ignition key, turn it from the ON gear to the ACC gear for 3 times, and finally stop at the ON position. At this time, the cab door lock pops up and the key is pulled out;

Pay attention to "A13552086073" for more surprises! Press the cab door lock again;

Press the remote control unlock key twice, the cab door lock pops up, and the first remote control is matched;

Then press the lock key of the second remote control, the cab door lock pops up, and the second matching is completed;

Match 6 keys at most, and the matching of the 5th and 6th keys must be completed within 5s.

Description:

If you want to add a remote control key, you must start with the first one when matching. Once you re-match, the previously matched remote control will be eliminated. The above methods are difficult to succeed at one time, and can be repeated many times.

13. Volkswagen Passat B5 remote control settings

Method 1:

Press the open button or close button of the remote control key once, keep it for about 1 min, the car is still locked, and then the remote control will recognize an effective fixed code;

Now use the remote control key to open or close the door mechanically once;

The tooth of the key will be recognized as a valid mechanical code, a new code will be exchanged between the car key and the controller, and the synchronization process will end.

Method 2:

Insert a key into the ignitiON switch "on" position;

Close all the doors and insert another key into the left door lock cylinder;

Press "Close" on the remote control, and at the same time turn the key to lock it for 3s;

Turn the key to "ON", turn the door and keep it for 3s;

Return to the original position and pull out the key. Pay attention to "A13552086073" for more surprises!

If you can't open the car by manipulating the remote control key, it may be that the code of the key is inconsistent with the code of the remote control in the car, or it may be that the launch button of the key is often manipulated outside the effective range of remote control, or the battery is defective. At this time, the remote control key must be resynchronized, and the synchronization process should not exceed 1min.

14.2012 Volkswagen New Polo Remote Control Key Matching

Remote control key model 202AD；; Chip, Vvdi uses 8.1 plug-in software. The specific steps are as follows:

Automatic diagnosis type;

Read EEPROM data;

Save; Pay attention to "A13552086073" for more surprises!

Reading anti-theft data;

Save;

Generate a dealer key;

Add a key.

Remote control: X431→09→10→00→01 Once confirmed, press the remote control 4 corner light to flash, and it is successful.

15. Volkswagen Magotan Remote Control Matching

The model of the remote controller is 1K0 959 753N, and 5053 is used to enter the 09 central electrical system.

Click Match 10, select 01 for the channel number, write 1 for the new value, test and save; Pay attention to "A13552086073" for more surprises!

Press the car lock key of the remote control, and when you see the double flashing lights of the instrument flashing, you can release the remote control;

Remote control matching is successful. Pull out the key and get off the bus to test whether it is successful or not.

16, 2014 LaVida remote control matching operation method

1. Select 09 electric central electronic equipment.

2. Select 【 10 Channel Adjustment and Matching 】.

3. Select "Read by List".

4. Select 【 000 Clear Learned Value 】.

5. Select "OK" in the lower right corner to prompt "Learning value cleared successfully".

6. Select "Read by List".

7. Select 【 001 Remote Control Adaptive 】 and confirm.

8. Enter a matching value of 0, and click OK.

9. Prompt for input data, enter 001, and select Save. Note that after "saving" the matching value, quickly press the key of the remote control car key for at least one second, so that the car ECU can recognize the remote control signal and complete the matching;

10. When the prompt channel is successfully matched, the remote control key is successfully matched. You can only match one at a time. If you want to match more than one, repeat the above matching operation.